Jump to content

Going to or have just brought a Dolls House


Recommended Posts

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By JLP
      Help! I started my first dollhouse and FINALLY got to a finishing point after about a year and a half. There are still a few minor things that need done but it’s finished enough for now (I needed to finish it by Xmas for my daughter). I have made dozens of little 1:24 models in the past and am a little knowledgable in electrical (aircraft electrician over a decade ago) but have since become rusty in the topic. I opted to install 6, small LED lights into the dollhouse, connected by a series of 9v batteries. Since my other smaller models have included similar setups with the LEDs and batteries, I didn’t think this would be an impossible task. I have ordered 9V lights and hardwired them into the house, connecting them in series to 6, 9v battery housing and a switch. It had seemed a bit of overkill to me, since the smaller models often used a single AA battery for often up to 4-5 bright lights. Except, it was very dim (which I don’t mind too much, as it’s more for effect anyway) and lasted maybe 30 minutes before dying. I’m lost now on what to do. I would have to completely cut into the house and moulding to replace the wiring. Thoughts? Did I completely mess this up? Help!! I will try to post pictures of the setup. 
    • By Littlehousesplus125
      You might like to look @ this if you were lucky enough to get a doll's houses at Christmas
       




    • By JenColes
      Good day! This is my first post in the forum - go easy on me!
      I'm an absolute beginner, currently building a 1:18 scale recreation of a local heritage house that was torn down 4 years ago. So far things are going well, but like MANY miniature newbies, I am absolutely confused by the wiring aspect of the build.
      I have done as much internet research and forum reading as I can, but I'm still not sure if I'm doing the correct thing.
      So, here it goes. These are my supplies:
      Cir-Kit Basic Wiring Kit
      Transformer (FIFODR® 12V 5A 60W DC Power Supply Adapter(Input 110V-220V,Output 12 Volt 5 Amp 60 Watt) DC Converter LED Driver Lighting Transformer for 12V 5A Flexible/Rigid 5050/3528/2835/5630/5730 LED Tape Strip Light FD-ADP60W)
      Lights (Pre Wired DC 9-12V 3mm Water Clear LED Diodes White Light)
      First question: Will the lights I purchased work with the tape wire kit?
      Second question: I will obviously need to purchase extension wire for the lights - what type of wire am I looking for?
      Third question: My house is mostly foam core on the inside, but the outside walls will be wood. I'm thinking of only installing the tape wire to the wood outer structure and laying/hiding the wire through the house, linking to the outside tape wire (does that make sense?). Will that work?
      Thanks in advance for any help you can provide!!
      Cheers
      Jen
    • By fleabags3
      OH MY.  I'm a doof.  I took a loooong break from minis and am firing it up again, but have had to refresh on many things.   I did the biggest rookie mistake. i spent so much wasted time meticulously installing wall sconces  so the wires were under wallpaper and just realized they make ADAPTERS for them. i'd only done ceiling lights and wall plugs.   duh me.  They look good but such a royal pain to noodle it all through the hardest way possible.  ugh
       
       
×
×
  • Create New...