Recently Browsing 0 members
No registered users viewing this page.
Hi everyone! I've had a long quiet period on here, but I've been steadily working away and going to shows/shops (I was at Good Sam in San Jose and was fortunate to visit Dollhouses, Trains, and More in Novato, CA for their closing sale). I will, finally, post a batch of haul and progress photos in the first week of November, when I get settled back into my home in Eugene. I really am terrible with a camera and it bugs everyone I know! In the meantime, I have a question:
Has anyone ever tried adding siding after their build's exterior was complete? Still being a novice, when I finished my first build (the Orchid; the interior is still a work-in-progress) I stepped back and thought 'I think I should have done siding.' Especially with the shingles on, the level of detail on the exterior just varies too much; it's been irritating me for a couple of months now. I'm a bit of a stickler it seems (though I didn't know it at the time)! My window/door casings, dormers, gingerbread, and my custom porch/railings are all already in place. I realize it may be very difficult, but the question is: is it even possible? If so, do you have any tips on how to do this?
Any and all possible mini wisdom is welcome!
P.S. I have the opportunity to snag a very affordable Laurel kit secondhand so I'm trying to decide where I should just start the next building with siding and call it 'lesson learned' or go back and add to the Orchid (and stash the Laurel until after the New Year, space is a very important consideration here). P.S. P.S.: I'm not a Cher fan, but I took a page out of Elizabeth's book (Studio E miniatures) since I'm always charmed by her ability to make musical jokes in her posts/titles!
It finally occurred to me that I'm on a Greenleaf forum and I have never shared that Greenleaf has one of my favorite and most used products, but I'll get to that last. First a couple of questions.
Is anyone familiar with Greenleaf's vinyl tile flooring? Is it glossy, and if so, can it be dulled? I want a paved stone look throughout the entire first floor of my Creole plantation house. This product:
While I can do the paperclay method, I'm worried that is going to add a great deal of weight to an already very heavy house. It's Lawbre's Rosedawn and it weighs a lot even in its unfinished state.
Added weight brings up my other question. Can anyone recommend a good brick sheet? Something textured, embossed, with the appearance of real brick? I've in the past purchased a few printed sheets of brick from England just to see what they were like and, well, I'd use them on a child's dollhouse maybe but not something on which I'm going for realism. They look good but even when not up close they are very obviously just printed paper.
I've etched brick into joint compound (a lot of work but looks great!). I've done brick and stone out of egg cartons (also looks great!). The joint compound will make this house far too heavy, and there is no way in heck I am cutting thousands of individual bricks out of egg cartons! I am seriously hoping there's some product out there that would work.
Okay, so there are my questions, now allow me to sing Greenleaf's praises for one of their products that is one of my favorites and most used. Their siding:
OMG have I bought bags and bags of this stuff over the years. It's admittedly a bit rough and I probably wouldn't use it to side a gleaming mansion, but it has so many other uses! Here are some that I've used it for.
It's perfect for siding a farmhouse or other "rustic" building. A simple wash gives it a fantastic aged appearance without a ton of work futzing around with multi-layers of painting and sanding and aging techniques. Some awful blurry old pics below of my farmhouse when it was in progress. I don't think they show just how fantastic that siding looked IRL.
Another pic below is a pic of a bedroom in (I think) Salem, MA. See that ceiling and that planked wall behind the bed? I used Greenleaf siding to recreate that and I was totally thrilled with the result. I also used Greenleaf's shingles on that same Colonial. The front was clapboard but I shingled the sides. I needed smaller shingles because historically those were pretty narrow. I simply snapped 'em in half, no scoring required.
The first floor of my Creole is going to be pretty "raw", with exposed brick exterior walls, but the interior walls of the first floor will be exposed planks behind stud framing. I'll be using even more Greenleaf siding for that. It's 3/4" wide so I'm going to score it at 1/2". The half-inch planks will be for the wall framing, the remaining 1/4" will be the equivalent of 3" lathing for the attic ceilings. And, of course, loads of it to plank almost all of the ceilings!
So there are a few of my handy-dandy uses. And at $5.00 for 360 square inches, I challenge anyone to find a better deal! If you could even find something that works half as well. Do you have other-than-intended uses for the siding or other products?
Edit: And oh yeah, it worked fabulously well for horizontal planked wainscoting in that Colonial house. I was going for a very early Colonial look so I didn't want any fine mouldings. That siding did the trick!
I am finally hoping to start on my own dollhouse after renovating a dollhouse for my toddler.
I am thinking about the weight of the house, as well as cost and have searched and searched and have not found as many photos of siding made with cardboard or upholstery strips.
I would love to see some examples! Thank you
I have also attached a picture of my dh, it is front opening and I will be making some modifications to the exterior to add modern touches and am also thinking of cutting windows on both sides.
By enchanted 1970's house
Hello everyone! I'm new at this stuff, but I've been reading this forum for months and I've learned so much from you all. Finally realized I should register. I'm hoping you can advise me on one issue...
I'm attempting to renovate a large 1970's dollhouse that originally had no siding. Very carefully I glued on clapboard siding (the kind that comes in overlapping wooden sheets) using Beacon Quik-Grip. After letting each side dry overnight, weighted down and taped, I began to paint it with Kilz primer and regular latex house paint. And then... horrors! The siding began to warp a bit and came up in a few spots! The water-based paint must have overwhelmed the sticking power of the glue.
But even so, the warping was minor enough that I thought I could just get away with squeezing more glue under the lifted edges and weighting them down. It was still not quite as even as it had been before painting, but it seemed... okay.
But THEN... we went away from the house for a couple of hot summer months, and when we came back I saw that the humidity had done a number on the siding. MORE warping! I ended up scraping off one entire side of it.
Do you have any advice to keep this from happening again? Is there another kind of paint I could use that might impart less moisture to the wood?
I'm looking to buy some siding sheets for my San Francisco house and I'm confused with the imperial sizes. I'm interested in your opinions on the right size (height wise) siding for 1:12. The options where I'm looking to purchase are 1/2 inch or 3/8 inch.. which is better for scale in your opinion?