Jump to content
stickyfingers

Can we talk about round wiring?

Recommended Posts

So, I need to add at least two lights to the current build. One will be an outdoor light that goes on the wall over the center of the door, and the other will be a wall sconce in the bathroom.

I hate to sound dense, but other than using a false wall on the interiors, how do I hide the wire? Both lights will have a hole drilled in the wall, with the wire fed through to the other side of the wall. I may use LED/battery powered lights for the rest of the rooms, so I'm not sure that I need to wire the whole house. Planning to use small battery packs (hidden in furniture) for the two lights in question.  

Any thoughts? Suggestions?

Share this post


Link to post
Share on other sites

Are you using siding on the house? The wire for the light over the door might go behind the siding and then follow down along the door frame. Where it comes through on the inside depends on how/where you hide the battery pack. It might run along behind a baseboard to reach the battery pack.

Might the bathroom wall sconce go directly over a mirror, which could hide the wire? Or beside a picture that is placed so that the wire could run horizontally toward a window and then drop down hidden by the curtain to a laundry basket or something that would hide the battery pack?

If you don't want to cut channels, I think you need to settle on the contents of the room, figuring out how to place them strategically.

Share this post


Link to post
Share on other sites

The house is made of MDF with the siding already milled. I'm planning to do planked walls for most/all of the interior. Planks would cover the wiring, but do I really want to glue planks over the wires?

For the bathroom, the setup will be sconce/mirror/vanity, but there will be exposed wall in between. For the exterior light, I could run the wire along the door frame, or run it up into the second floor and hide it behind the baseboard, but again, there will be a section of wall that the wire will cross. I did think of adding hollow beams, like Brae did for her barn build, but I think for it to look "right" I'd need to add beams to the whole thing, and I'm not sure I want to do that, either.

If someone would just make all of the lights that I want in LED it would solve all of these issues!   

Share this post


Link to post
Share on other sites

Why not make templates of your walls and plank/ paint/ paper those?  You can attach the templates with poster putty or some other removable adhesive to the edges so they can be removed, if necessary, for troubleshooting wiring later or to redecorate..

Share this post


Link to post
Share on other sites

Someone told me that a light will fail at the power source or at the bulb, but not at the wire, so it's OK to glue the wire down, paper over it, etc. That said, it seems so irrevocable. Could you make your own frankenlight by putting a LED into an existing fixture? Maybe a less expensive, non-working fixture?

Share this post


Link to post
Share on other sites

The wire will not fail as long as it isn't cut. I hide mine under the baseboards.

If you put in a wood floor and leave 1/16" around the edges and then  slightly sand the bottom back of the baseboard it the electrical wire will tuck right in the slot.

Yes you can put an LED light set into an existing light, but it's easier to make the light, especially table lamps, from scratch.  

Share this post


Link to post
Share on other sites

I sometimes dremel a line for the wires, and run my wire thru a small straw, and tuck in extra wire, that way I can pull out the light, to change bulbs, and tuck it back in.  I usually paint card stock and glue that to the wall,and no glue gets onto my wires

tucking that wire back in is not fun though.

my last house I expermint end with snot gluing down ten floors,a no my wires are under the floors.  But I just noticed today one floor is warping up.  Grr

Share this post


Link to post
Share on other sites
47 minutes ago, smjsome said:

my last house I expermint end with snot gluing down ten floors,a no my wires are under the floors. 

There has to be a couple typos in the sentence, yes? :ermm: 

Share this post


Link to post
Share on other sites

Auto correct - it's not my friend.

i experimented with not gluing down the floors, running the wires under, and one of my floors is warping.  Dang iPhones.  

  • Like 1

Share this post


Link to post
Share on other sites

But.... snot glue..... I know that works great!  I'm a pediatrician and work with it all day long.   :-p

  • Like 1

Share this post


Link to post
Share on other sites

Kathy, I was an elementary school nurse for several years and that is a substance with which I am all too familiar...

  • Like 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


  • Recently Browsing   0 members

    No registered users viewing this page.

  • Similar Content

    • By JLP
      Help! I started my first dollhouse and FINALLY got to a finishing point after about a year and a half. There are still a few minor things that need done but it’s finished enough for now (I needed to finish it by Xmas for my daughter). I have made dozens of little 1:24 models in the past and am a little knowledgable in electrical (aircraft electrician over a decade ago) but have since become rusty in the topic. I opted to install 6, small LED lights into the dollhouse, connected by a series of 9v batteries. Since my other smaller models have included similar setups with the LEDs and batteries, I didn’t think this would be an impossible task. I have ordered 9V lights and hardwired them into the house, connecting them in series to 6, 9v battery housing and a switch. It had seemed a bit of overkill to me, since the smaller models often used a single AA battery for often up to 4-5 bright lights. Except, it was very dim (which I don’t mind too much, as it’s more for effect anyway) and lasted maybe 30 minutes before dying. I’m lost now on what to do. I would have to completely cut into the house and moulding to replace the wiring. Thoughts? Did I completely mess this up? Help!! I will try to post pictures of the setup. 
    • By Littlehousesplus125
      You might like to look @ this if you were lucky enough to get a doll's houses at Christmas
       




    • By Littlehousesplus125


      Dolls House wiring specialist from Small world Products


       
      Wiring a Doll’s House here is some information you might like to look at, it all works around our SWP Easy-Wire system wiring a Dolls House 1/12th or 1/24th
      Have you check out our YouTube channel

      https://www.youtube.com/user/littlehousesplus125/videos

      There is a lot of information on our Doll's House wiring for Lighting / Fires page

      http://www.littlehousesplus-shop.co.uk/epages/62053002.sf/en_GB/?ObjectPath=/Shops/62053002/Categories/Dolls_House_wiring

      And if you need any help here is the link for you

      http://littlehousesplus.co.uk/about_us_2.html

      By the way we send all over the world

      There are lots more on http://www.littlehousesplu-shop.co.uk




    • By JenColes
      Good day! This is my first post in the forum - go easy on me!
      I'm an absolute beginner, currently building a 1:18 scale recreation of a local heritage house that was torn down 4 years ago. So far things are going well, but like MANY miniature newbies, I am absolutely confused by the wiring aspect of the build.
      I have done as much internet research and forum reading as I can, but I'm still not sure if I'm doing the correct thing.
      So, here it goes. These are my supplies:
      Cir-Kit Basic Wiring Kit
      Transformer (FIFODR® 12V 5A 60W DC Power Supply Adapter(Input 110V-220V,Output 12 Volt 5 Amp 60 Watt) DC Converter LED Driver Lighting Transformer for 12V 5A Flexible/Rigid 5050/3528/2835/5630/5730 LED Tape Strip Light FD-ADP60W)
      Lights (Pre Wired DC 9-12V 3mm Water Clear LED Diodes White Light)
      First question: Will the lights I purchased work with the tape wire kit?
      Second question: I will obviously need to purchase extension wire for the lights - what type of wire am I looking for?
      Third question: My house is mostly foam core on the inside, but the outside walls will be wood. I'm thinking of only installing the tape wire to the wood outer structure and laying/hiding the wire through the house, linking to the outside tape wire (does that make sense?). Will that work?
      Thanks in advance for any help you can provide!!
      Cheers
      Jen
×
×
  • Create New...