Search the Community
Showing results for tags 'tape wire'.
-
I have begun installing lights in the Beacon Hill. In past builds, I have wound the fixture wire around a brad or eyelet to affix it to the tape. No need to remove the protective plastic covering but always the fear of a connection wiggling loose and failing. This time I want to solder the wires to the tape wire, which means removing a small square of the protective plastic layer to expose the metal beneath. I tried to be delicate with a scalpel on the first one, but managed to cut the metal strip anyway, which of course cut the power to the rest of the house. I was able to reconnect it with solder, but am now leery of cutting across the tape wire. For the second fixture, I used the edge of the soldering iron to melt two parallel lines across the metal strip and carefully cut lines parallel to the tape wire to remove a square of the protective covering. That left plastic residue on the soldering iron and did create some smoky odor. Question 1: How else can a patch of plastic be removed to provide a clean shot at the tape wire beneath to assure a strong solder joint? Question 2: How do you prepare the bare wire for the smoothest attachment? I've tried twisting the strands into one multi-strand and bending into a circle for maximum surface. Is there a better way? The photo is of my practice with the new soldering iron. Can't tell if the joints are good, as the wires are not attached to anything.
-
I'm updating my childhood dollhouse (Stanley Colonial) and using tape wire for the first time. I could really use some advice This is a large, two-sided dollhouse and would appreciate your thoughts on how best to run the main line to get to both sides. I'm planning to add a false-bottom that the main line can come up from. Also of note..the chimney is essentially a large hole that goes straight down until it hits the thick wood base. Wondering if this would be the best place to come up from the false bottom. There are 7 fireplaces, but I'm thinking maybe the fireplace on the back side would be good to light up since it's the only visible one. Photos show the dollhouse with doors and roof off. I'm hoping to get all the tape wire set-up then work on one side so that my niece can start playing with it while I finish the opposite side.
-
Good day! This is my first post in the forum - go easy on me! I'm an absolute beginner, currently building a 1:18 scale recreation of a local heritage house that was torn down 4 years ago. So far things are going well, but like MANY miniature newbies, I am absolutely confused by the wiring aspect of the build. I have done as much internet research and forum reading as I can, but I'm still not sure if I'm doing the correct thing. So, here it goes. These are my supplies: Cir-Kit Basic Wiring Kit Transformer (FIFODR® 12V 5A 60W DC Power Supply Adapter(Input 110V-220V,Output 12 Volt 5 Amp 60 Watt) DC Converter LED Driver Lighting Transformer for 12V 5A Flexible/Rigid 5050/3528/2835/5630/5730 LED Tape Strip Light FD-ADP60W) Lights (Pre Wired DC 9-12V 3mm Water Clear LED Diodes White Light) First question: Will the lights I purchased work with the tape wire kit? Second question: I will obviously need to purchase extension wire for the lights - what type of wire am I looking for? Third question: My house is mostly foam core on the inside, but the outside walls will be wood. I'm thinking of only installing the tape wire to the wood outer structure and laying/hiding the wire through the house, linking to the outside tape wire (does that make sense?). Will that work? Thanks in advance for any help you can provide!! Cheers Jen
-
Hello Everyone! I just discovered this forum and am so grateful! I am remodeling my childhood dollhouse that my dad made for me. I have cleared out the entire house of everything including wallpaper and flooring. I have left the existing electric tape and would like to add on to it seeing as though it still works. I bought the blue and copper tape wire to use throughout the house and am wondering how to attach it to the existing tape wire which is two copper pieces (no blue piece). Is it possible? I assume there is a way. I have also purchased brads to use in connecting them. From reading some other posts am I correct in thinking I should purchase eyelets instead? Thank you, Kouwe
- 12 replies
-
- tape wire
- electricity
-
(and 3 more)
Tagged with:
-
Hello! I THINK I want to wire my Beacon Hill (bought used so renovating, not made from kit) I have the large cir-kit tape wire kit unused from my voyage to minis years ago. Honestly it scares me to pieces to think of doing it, but I bet once I start it's easier than it sounds! BUT the problem is that I wasn't planning to wire it, and I've glued panels to the walls of the main foyer room! They are not floor to ceiling, but are only 3 inch by 1 inch panels, glued about half inch from the floor. Since they stick out I don't think I can just tape wire over top of them. I know you're supposed to be about an inch or inch and a half from the floor, and consistent throughout the house, so I'm not sure how or if I could wire it now. None of the other rooms have had anything done. I have wallpaper for the main entry and a few other rooms, so I need to figure this out before I move forward. How can I make it work? Could I tape the left and right rooms all the way around in the traditional way, and then the entry just for a chandelier?? Could I wire that one room just above the panels? (By going around the bottom of the left/right, then up that wall, into the foyer above the panels, around the foyer, add ceiling wires, then down the wall of the right/left and around the lower area of that room?) Also, can I wire it now, then decide lighting placement later? Or do I need to know exactly what lights I'm using and where they are going before I wire???? And, one more, how obvious are the plugs for lights when you use them?? Do they plug into the house wall similar to how they plug into a real wall? I can't visualize how it works when I know there are wall sconces too, and where those wires go. Thanks!!!